Grant-instruments Labwise Manual de usuario

Busca en linea o descarga Manual de usuario para Software Grant-instruments Labwise. Grant Instruments Labwise User Manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir

Indice de contenidos

Pagina 1 - Labwise

Labwise Operating Manual

Pagina 2 - May 2012 Page 2 30853(1)

May 2012 Page 10 30853(1) 3.0 Main control window 3.1. Overview Labwise opens the main control window at start up. This window shows real tim

Pagina 3 - 30853(1) Page 3 May 2012

30853(1) Page 11 May 2012 There are four checkbox indicator/controls:  Relay 1  Relay 2 (only enabled for the GP200)  Logging  External

Pagina 4 - May 2012 Page 4 30853(1)

May 2012 Page 12 30853(1) 3.5. Bath setup The key settings on the Optima can be changed by selecting Bath from the Setup option on the main co

Pagina 5 - Table of Contents

30853(1) Page 13 May 2012 3.6. Logging setup The data logging settings can be changed by selecting Logging from the Setup option on the main c

Pagina 6 - 1.0 Introduction

May 2012 Page 14 30853(1) 4.0 Programs 4.1. Overview A program allows the temperature and pump speed of the Optima to be controlled with time.

Pagina 7 - 30853(1) Page 7 May 2012

30853(1) Page 15 May 2012 4.3. Creating a new program A new program can be created by selecting New from the File option on the program window

Pagina 8 - May 2012 Page 8 30853(1)

May 2012 Page 16 30853(1) 4.3.1.2. Extension The Extension is a time period in addition to the Duration. A segment with an Extension period set

Pagina 9 - 30853(1) Page 9 May 2012

30853(1) Page 17 May 2012 4.3.2. Setting program alarms Program alarms are used only when a program is running. They are global program parame

Pagina 10 - 3.0 Main control window

May 2012 Page 18 30853(1) 4.4. Edit a program 4.4.1. Edit a program previously saved to disk Programs that had been saved to the PC can be o

Pagina 11 - 30853(1) Page 11 May 2012

30853(1) Page 19 May 2012 4.5. Deleting a program installed in the Optima A program that is stored in the Optima can be deleted to free up a s

Pagina 12 - May 2012 Page 12 30853(1)

May 2012 Page 2 30853(1) Grant Instruments, based near Cambridge, England, is an independent, privately owned company, founded in 1951 by Peter W

Pagina 13 - 30853(1) Page 13 May 2012

May 2012 Page 20 30853(1) 5.0 Creating reports 5.1. Creating a report The Reports option allows data logs to be viewed and printed if requi

Pagina 14 - 4.0 Programs

30853(1) Page 21 May 2012 6.0 Calibration (GR150 & GP200 only) 6.1. Performing a single point calibration A single point calibration ca

Pagina 15 - 30853(1) Page 15 May 2012

May 2012 Page 22 30853(1) 7.0 Technical Support Service Address: Grant Instruments (Cambridge) Ltd 29 Station Road Shepreth

Pagina 17 - 30853(1) Page 17 May 2012

Grant Instruments (Cambridge) Ltd Shepreth Cambridgeshire SG8 6GB England Tel: +44 (0) 1763 260811 Fax: +4

Pagina 18 - May 2012 Page 18 30853(1)

30853(1) Page 3 May 2012 Grant Software License Agreement This is a legal Agreement between you, the user, and Grant Instruments (Cambridge) Ltd

Pagina 19 - 30853(1) Page 19 May 2012

May 2012 Page 4 30853(1) General The above terms constitute the entire agreement between you and Grant with regard to the Software. If any provi

Pagina 20 - 5.0 Creating reports

30853(1) Page 5 May 2012 Table of Contents 1.0 Introduction 6 2.0 Installation & connection 6 2.1. Minimum system requirements 6 2.2.

Pagina 21 - 30853(1) Page 21 May 2012

May 2012 Page 6 30853(1) 1.0 Introduction Labwise is a PC software application that provides configuration and remote control of OptimaTM imme

Pagina 22 - 7.0 Technical Support

30853(1) Page 7 May 2012 Use the following process for installing the software: 1. Insert the USB flash drive into a USB port on the PC. The dr

Pagina 23

May 2012 Page 8 30853(1) 2.6. Installing Optima USB drivers (Windows XP) The Labwise installation process must be completed prior to attempting

Pagina 24

30853(1) Page 9 May 2012 2.7. Installing Optima USB drivers (Windows Vista/7) The Labwise installation process must be completed prior to attemp

Comentarios a estos manuales

Sin comentarios